How to clone your penis?

[Husky_Embrace]

So I've tried to clone my cock three times. All three were failures. I wonder if people have suggestions how to do it.

I used clone a willy. The first time it was my own fault. It was too close to the edge, so that instantly failed when I removed my penis. However, another problem already showed it's face. Suction.

They recommend removing your penis after a bit. Iirc 2 minutes. It has been a while since I last tried. However, the thing is sealed quite well. That I get a bit wider at the middle might also not help. This results in me having to wait until I get much less hard, but the damage is done. There's just a smooth big hole that looks nothing like a penis.

At this moment I'm doubting if it truly works at all. It seems flawed from the beginning, as I simply can't follow the pull out instruction without feeling my cock is going to be ripped off, and not succeeded until minutes later when my hard-on finally subsides.

Are there things I can do differently, like the smallest straw alongside to offer air when I rip that out first or something? Is there maybe a better kit that does work?

 

[Ellies_adventures]

Thanks for the 'heads' up, I had often wondered how they work, and after reading that don't think i will ever waste my hard earned on the clone a willy

 

[Britva415]

I simply can't follow the pull out instruction without feeling my cock is going to be ripped off

Try breaking the seal at the edge, at the base of your cock, instead of just trying to pull straight out without opening a space. Use your other hand to open up a little space between the mold material and your cock. Air will enter the mold through that space so that your dick isn't vacuumed in there.

 

[MasterDarcy]

3D printer?

 

[Husky_Embrace]

Try breaking the seal at the edge, at the base of your cock, instead of just trying to pull straight out without opening a space. Use your other hand to open up a little space between the mold material and your cock. Air will enter the mold through that space so that your dick isn't vacuumed in there.

A good idea, but from my asymmetrical shape, widening from the base towards the middle, it would mean I would need to break the seal until that point. Not to mention that the cap is also wider than the shaft. It did not work for me.

I'm still thinking if a very thin straw or something along the edge of the shaft or pushing it though a hole on the back to give air a chance. However, I'm not too happy for the chance of failure even with such things in place, not to mention I'll need to fix that part after the fact.

3D printer?

How expensive would that be? There are these scanners nowadays. Maybe it's possible. After the scan you'll make it a negative to print the casting mold. Then you can surprise everyone with tiny chocolates that vibrate off your teeth.

 

[MasterDarcy]

How expensive would that be? There are these scanners nowadays. Maybe it's possible. After the scan you'll make it a negative to print the casting mold. Then you can surprise everyone with tiny chocolates that vibrate off your teeth.

Honestly, I was joking. But apparently you can do it with a 3D printer.

Huh. What a time to be alive.

3D printers are not cheap.

https://www.reddit.com/r/3Dprinting/comments/u35te9/advice_on_how_to_3d_cloneprint_my_partners_penis

 

[ICantLeafYou]

I don't have any advice, but I do wonder--what are your plans for the toy when [if...] you successfully get it done? Fuck yourself? Suck on it? Play with a partner? DP with two of your cocks, hmm...

I find the idea of a man fucking himself with his own cock extremely arousing and even wrote a story about it.

 

[NOBGE]

So I've tried to clone my cock three times. All three were failures. I wonder if people have suggestions how to do it.

I used clone a willy. The first time it was my own fault. It was too close to the edge, so that instantly failed when I removed my penis. However, another problem already showed it's face. Suction.

They recommend removing your penis after a bit. Iirc 2 minutes. It has been a while since I last tried. However, the thing is sealed quite well. That I get a bit wider at the middle might also not help. This results in me having to wait until I get much less hard, but the damage is done. There's just a smooth big hole that looks nothing like a penis.

At this moment I'm doubting if it truly works at all. It seems flawed from the beginning, as I simply can't follow the pull out instruction without feeling my cock is going to be ripped off, and not succeeded until minutes later when my hard-on finally subsides.

Are there things I can do differently, like the smallest straw alongside to offer air when I rip that out first or something? Is there maybe a better kit that does work?

Helps to have your partner helping out. Did the clone a wily. Followed the directions and worked well. She has it for when she needs.

 

[Husky_Embrace]

I don't have any advice, but I do wonder--what are your plans for the toy when [if...] you successfully get it done? Fuck yourself? Suck on it? Play with a partner? DP with two of your cocks, hmm...

I find the idea of a man fucking himself with his own cock extremely arousing and even wrote a story about it.

I would like to feed your fetish, but unfortunately it is for other reasons. I'm true to my partner, but there's women who are still curious. Besides that, you can do some ludicrous things with it. Like making chocolate.

Helps to have your partner helping out. Did the clone a wily. Followed the directions and worked well. She has it for when she needs.

How does a partner effectively help out? How did you pull out?

 

[NOBGE]

I would like to feed your fetish, but unfortunately it is for other reasons. I'm true to my partner, but there's women who are still curious. Besides that, you can do some ludicrous things with it. Like making chocolate.


How does a partner effectively help out? How did you pull out?

She made sure I got hard and stayed hard! Plus she did the mixing and pouring. Don’t remember how I pulled out.

 

[jassybb]

OMG, that's the first time i have heard about penis cloning, I did not know it was a thing people do

 

[NuclearFairy]

I remember in art class they had us covering our faces in vaseline before we made a mold of our faces. But that was quite some time ago, and I don't know if plaster molds are anything like the kind of mold you're using.

Another thing you could try would be to wear a condom while making the mold. Then if you need to get off before getting out you wouldn't make quite as much of a mess.

 

[Husky_Embrace]

OMG, that's the first time i have heard about penis cloning, I did not know it was a thing people do

We're men. If it has anything to do with penis, it exists.

I remember in art class they had us covering our faces in vaseline before we made a mold of our faces. But that was quite some time ago, and I don't know if plaster molds are anything like the kind of mold you're using.

Another thing you could try would be to wear a condom while making the mold. Then if you need to get off before getting out you wouldn't make quite as much of a mess.

I'm not sure where the orgasm is coming from. The vaseline is a good idea. I'll still have to solve the suction problem, but I'll get creative next time. The condom less so. You want it in detail. The condom would hide many features.

 

[jassybb]

We're men. If it has anything to do with penis, it exists.

haha