Advice...? Off Topic?

Re: some of what you wrote there, scares me, Zam

erosman said:
The car jack will be enough. Yes, you will need to remove the wheels/tires. Where do you live, Zam? Ask your neighbor. Like you mentioned, ask at work. I have a friend whose colleagues from work pool their time and talents and fix everything on each other's cars. Network.

Thanks Eros...Richfield, Mn...Five minutes from the Mall of America.
 
Zamdrist said:
Ok...ok...

I do have ratchets and sockets of all sizes. But I don't have anything to lift the back end up with (Other than the tire jack that comes with the car I suppose) Would I need to? Which tools might I likely need? Thanks...

You can just use that jack and you will be ok as long as, and I can't stress this enough, never, ever, ever, ever put any part of your body under the car.

Those jacks can fail if they are holding the car up for a long period of time.

I would put a cinder block under the car and bring the jack down so that some of the weight is resting on it.

You will probably need a Large C-Clamp to compress the piston in the caliper to remove it. You don't always need one of these but they help and you can get them at wal-mart or Sears.

You will also need a wire hanger to hang the caliper from once you have it unbolted. You don't want to ever let the caliper hang from the rubber brake hose that is attached to it so just use a wire hanger to hook it to something on the car.

I can't think of anything else off the top of my head that you don't already have.
 
Zam, I am too far to help. Minnesotans are great for helping. You sound genuine, and that goes a long way when you ask for help.
 
Thanks to all of you for the advice and consideration. You are all wonderful.

Thanks :)
 
Azwed said:
I know several people here(WH, STG, LC, off the top of my head) have good mechanicle experience and any one of them could help probably help you out.

My father was a certified Master Service Technician for nearly 30 years -- That makes me as mechanical as a preacher's kid is righteous!

Zam, Spend a few minutes browsing the Yellow Pages for "Brake Repair" shops. I'msure you can find a Midas, Minecke or other place that specializes in brake repair that will replace the pads and turn the rotors -- the best option unless they've been turned before -- for a lot less than $300+

The last time I had brakes done, it was about $250 for both front disk brakes and rear drum brakes on a 1986 T-10 Blazer -- that included turning the drums and rotors. Midas did the work.

A couple of questions:

Is the squeal from the rivets eating the rotors or from the wear indicator?

Disk brakes have a metal device that causes a noise when the brakes are worn, but not worn-out. If it's the wear indicator making the noise, you're safe to drive for several hundred miles before the brakes become really hazardous.

Are the front brakes the same age as the rear?

If the rear brakes are wearing out before the front brakes then you may have a more serious (and expensive) problem than wear. The front brakes take about 60% of thebraking load in normal circumstances and should be worn more than the rear brakes. If the rear are wearing out first, youmay have a problem with the "proportioning valve."

Changing the brake pads yourself is actually a fairly simple process -- very messy, prone to claiming large chunks of flesh from your knuckles and has a potential to make your vehicle very dangerous if screwed up -- and can save you a bundle of money.

However, I'd strongly recommend having a professional do any brake work -- especally if the rotors need turned or replaced.
 
Emerald_eyed said:
Is that the spring thing??
I mean I was doing breaks with my ex, and we could NOT get that thing to queeze right, until we bought that tool. Then it was quick

He got the tools in the divorice, or Id meet ya to give it you you ZAm\considering Im about 3 hours away

I think you mean a spring compressor. There are lots of types of spring compressors but the one you are talking about is for the springs on the shoes of drum brakes. You don't have to worry about that with Rotor/caliper based brakes.

Sometimes you can wiggle the caliper off the rotors without the C-Clamp but that does not always work. The C-Clamp makes it way easy.
 
Weird Harold said:
Is the squeal from the rivets eating the rotors or from the wear indicator?

Are the front brakes the same age as the rear?

I have no idea on either question. I'm assuming because the estimate indicated 'wear' it would be from the wear indicator...? But right now I can only assume that.

As far as the age of the front and rear breaks I couldn't tell you. I bought the car about 1 1/2 years ago, and it's a 96...so...<shrug>

Thanks. I can afford something between $100-300 more than $500+!
 
Zamdrist said:
I have no idea on either question. I'm assuming because the estimate indicated 'wear' it would be from the wear indicator...? But right now I can only assume that.

As far as the age of the front and rear breaks I couldn't tell you. I bought the car about 1 1/2 years ago, and it's a 96...so...<shrug>

If you're not sure, then get them fixed as soon as you can. The wear indicator should sound like fingernails on a chalkboard or like you're dragging something metal under the car.

Even if it's the wear indicator making the noise, the longer you wait, the more the rotor will be damaged, and the more likely it is that you'll need replacement rotors -- Waiting adds to the cost.

If you don't know how old the front brakes are, it might be prudent to have ALL the brakes done at the same time. At most Brake shops, that is still going to be in your price range of under $300.
 
Ah hell

Zam.. bring it on over.. I'll change the brakes for ya.. and you can sit and bullshit with Mr Freaky over a couple of beers. ;)

I'll even supply the beer for you to drink:D
 
freakygurl said:
Ah hell

Zam.. bring it on over.. I'll change the brakes for ya.. and you can sit and bullshit with Mr Freaky over a couple of beers. ;)

I'll even supply the beer for you to drink:D

:D
 
Job done

$232.59 @ Midas with a 25% off coupon from their website. Pads replaced, rotors resurfaced.

Thanks all for the advice.

Happy Holidays
 
Re: Job done

Zamdrist said:
$232.59 @ Midas with a 25% off coupon from their website. Pads replaced, rotors resurfaced.

Thanks all for the advice.

Happy Holidays

Great job. 232 sounds like a much more reasonable price then the earlier ones.
 
Back
Top